Calculation Study of Thermal Stresses in the Medium-Pressure Rotor of the K-200-130 Turbine During Start-Up from a Cold State

image_print
DOI https://doi.org/10.15407/pmach2024.02.036
Journal Journal of Mechanical Engineering – Problemy Mashynobuduvannia
Publisher Anatolii Pidhornyi Institute for Mechanical Engineering Problems
National Academy of Science of Ukraine
ISSN  2709-2984 (Print), 2709-2992 (Online)
Issue Vol. 27, no. 2, 2024 (June)
Pages 36-42
Cited by J. of Mech. Eng., 2024, vol. 27, no. 2, pp. 36-42

 

Authors

Serhii R. Lishchuk, National Technical University of Ukraine “Igor Sikorsky Kyiv Polytechnic Institute” (37, Beresteiskyi ave., Kyiv, 03056, Ukraine), e-mail: Serg23li231097@gmail.com, ORCID: 0000-0001-7874-5019

Vitalii A. Peshko, National Technical University of Ukraine “Igor Sikorsky Kyiv Polytechnic Institute” (37, Beresteiskyi ave., Kyiv, 03056, Ukraine), e-mail: vapeshko@gmail.com, ORCID: 0000-0003-0610-1403

 

Abstract

The paper is devoted to the study of temperature and stress distribution in the medium-pressure rotor of the K-200-130 turbine, which are of considerable interest when predicting the durability of this equipment and extending its operation beyond the service life. A geometric model of the most loaded part of the rotor – from the middle of the shaft neck in the thrust bearing area to the 5th stage disc – was developed. The study of the thermal and stress-strain state of the rotor during start-up from a cold state was performed in a two-dimensional formulation using the finite element method. The non-stationary problem of heat conduction during start-up was solved. The obtained results indicate a fairly uniform thermal state during variable operating conditions. The largest temperature gradient (1200–2200 K/m) is observed at the time points from the rotor push to the synchronization of the turbine generator with the power system. After the turbine generator is loaded with up to 30 MW of electric power, a decrease in the temperature field irregularity and its gradual stabilization are observed. It was found that when operating at the nominal steam parameters, the maximum metal temperature is 508 °C in the region of the control stage and decreases when the distance from it increases. The stress-strain state of the rotor was evaluated taking into account the unevenness of temperature fields during start-up, stresses from thermal expansion, and centrifugal forces. The highest stresses are characteristic of the moment when the turbine comes to idle in the area of thermal compensation grooves of the rotor and the control gate and amount to 440–472 MPa. It is noted that these areas are the most likely zones of ring crack nucleation during turbine start-up operations. Subsequently, the stress level gradually decreases as the turbine unit reaches its rated power. It has been established that the most stressed area of the rotor during stationary operation is the area of the axial bore under the control stage and its diaphragm seal (121–134 MPa).

 

Keywords: steam turbine, rotor, start-up, thermal state, stress state, temperature gradient, stress intensity.

 

Full text: Download in PDF

 

References

  1. Peshko, V. A. & Lishchuk, S. R. (2023). Upravlinnia vytratoiu palyva enerhobloka 200 MVt pry roboti v rezhymi chastykh puskiv [Management of fuel consumption of a 200 MW power unit when operating in frequent start-up mode]. Enerhetyka: ekonomika, tekhnolohii, ekolohiia – Power Engineering: Economics, Technique, Ecology, vol. 74, no. 4, pp. 128–133. https://doi.org/10.20535/1813-5420.4.2023.290940 (in Ukrainian).
  2. Rusin, A., Nowak, G., Łukowicz, H., Kosman, W., Chmielniak, T., & Kaczorowski, M. (2021). Selecting optimal conditions for the turbine warm and hot start-up. Energy, vol. 214, paper 118836. https://doi.org/10.1016/j.energy.2020.118836.
  3. Bovsunovsky, A., Shtefan, E., & Peshko, V. (2023). Modeling of the circumferential crack growth under torsional vibrations of steam turbine shafting. Theoretical and Applied Fracture Mechanics, vol. 125, paper 103881. https://doi.org/10.1016/j.tafmec.2023.103881.
  4. Wang, W. Z., Buhl, P., Klenk, A., & Liu, Y. Z. (2016). The effect of in-service steam temperature transients on the damage behavior of a steam turbine rotor. International Journal of Fatigue, vol. 87, pp. 471–483. https://doi.org/10.1016/j.ijfatigue.2016.02.040.
  5. Kang, M., Wu, S., Liu, Y.-Z., & Wang, W. (2023). Viscoplastic model-based analysis of in-service oscillation temperature and thermal stress in a rotating component. International Journal of Thermal Sciences, vol. 188, paper 108246. https://doi.org/10.1016/j.ijthermalsci.2023.108246.
  6. Sen, S. & Patel, B. P. (2023). Constitutive model based study to enable flexible operation of steam turbine rotors in Indian SPPs. Materialstoday: proceedings, vol. 87, part 1, pp. 314–323. https://doi.org/10.1016/j.matpr.2023.06.147.
  7. Liu, Y. & Wang, W. (2020). Evolution of principal stress of a turbine rotor under cyclic thermo-mechanical loading. Engineering Failure Analysis, vol. 109, paper 104242. https://doi.org/10.1016/j.engfailanal.2019.104242.
  8. Peshko, V., Ulitko, O., & Lishchuk, S. (2023). Otsinka perevytraty palyva enerhoblokom 200 MVt pry puskakh z riznykh teplovykh staniv [Estimation of fuel overconsumption by a 200 MW power unit during startups from different thermal condition]. Scientific Collection “InterConf+” with the Proceedings of the 1st International Scientific and Practical Conference “Modern Knowledge: Research and Discoveries” (May 19–20, 2023, Vancouver, Canada). 2023. No. 33 (155). P. 296–304 (in Ukrainian). https://doi.org/10.51582/interconf.19-20.05.2023.027.

 

Received 01 March 2024

Published 30 June 2024